Plan the prototype against the series build
Specify prototype and production quantities separately. If the prototype uses a different laminate, trace spacing or via construction, identify what needs to be requalified for production.
Send fabrication data that can be priced
Provide Gerber or ODB++, drill files, finished thickness, layer-specific copper and finish. Include start and stop layers for each via group and signal and reference layers for impedance lines.
Write acceptance into the order
Specify electrical testing, impedance records or cross sections where needed. Mark special areas such as gold fingers, hybrid laminates or back-drilled holes on the drawing.
Board types
Multilayer PCB
Multilayer boards for dense routing, power distribution and signal isolation, built to the stack-up agreed in engineering review.
- Stack-up proposed or checked against your targets
- Material selected for the application
- Layer count confirmed per project
HDI PCB
High-density interconnect boards for compact layouts and fine-pitch components.
- Via structure reviewed before quotation
- Fine-line routing checked in DFM
- Feasibility confirmed per design
Rigid-Flex PCB
Combined rigid and flexible sections that remove connectors and cables from compact assemblies.
- Bend areas and transitions reviewed
- Construction agreed with your drawing
- Assembly constraints discussed early
Flexible PCB (FPC)
Flexible circuits for moving parts, tight spaces and lightweight designs.
- Coverlay and stiffener options reviewed
- Bend requirements clarified
- Material confirmed per project
High-Frequency PCB
Boards for RF and microwave designs where dielectric properties and loss matter.
- Laminate options reviewed against your targets
- Hybrid stack-ups discussed when useful
- Material availability checked before quotation
High-Speed PCB
Boards for fast digital interfaces where signal integrity depends on materials and geometry.
- Low-loss material options reviewed
- Impedance targets checked with the stack-up
- Back drilling discussed where needed
Heavy Copper PCB
Boards for power electronics and high-current paths that need thicker copper.
- Copper weight and trace geometry reviewed
- Thermal needs discussed with engineering
- Parameters confirmed per project
Metal Core PCB
Metal base boards that move heat away from LEDs, power devices and drivers.
- Base material and dielectric options reviewed
- Thermal requirements clarified
- Construction confirmed per project
Backplane PCB
Large, thick boards that connect cards and modules in communication and computing systems.
- Stack-up and board thickness reviewed
- Press-fit and back drilling needs discussed
- Feasibility confirmed per design
Prototype & Quick-Turn
Early builds that validate your design, with the path to production planned from the first review.
- Prototype and production requirements kept separate
- Design feedback shared before the build
- Schedule confirmed in the quotation
Manufacturing capability by board type
Compare prototype and production limits for the construction you plan to order.
| Parameter | Prototype | Mass production |
|---|---|---|
| Layer count (max) | 50L | 36L |
| Finished board thickness | 0.2–15.0 mm | 0.3–7.0 mm |
| Thickness tolerance | ±8% | ±8% |
| Min trace / space | 2.5 / 2.5 mil | 3 / 3 mil |
| Min hole-to-trace clearance | 5 mil | 5 mil |
| Copper weight | 1/3–12 oz | 1/3–8 oz |
| Layer registration accuracy | 0.8 mil | 1 mil |
| Min through-hole diameter | 0.075 mm | 0.10 mm |
| Min blind via diameter | 0.05 mm | 0.075 mm |
| Max aspect ratio | 35:1 | 30:1 |
| Etching tolerance | ±10% / ±0.8 mil | ±10% / ±1 mil |
| Min solder mask bridge | 2 mil | 3 mil |
| Impedance control tolerance | ±5% | ±7% |
| HDI level | 9th order | 5th order |
| Surface finish | ENIG, electrolytic gold, HASL, Ni/Pd/Au, thick electrolytic gold, immersion tin, immersion silver, OSP, carbon | ENIG, electrolytic gold, HASL, Ni/Pd/Au, thick electrolytic gold, immersion tin, immersion silver, OSP, carbon |
| Material types | Shengyi, TUC, 建涛, Nan Ya, ITEQ, Rogers, 华正, Elite Material (EMC), Isola (Tg135 / Tg150 / Tg170, CAF resistance, CTI > 600, halogenated and halogen-free) | Shengyi, TUC, 建涛, Nan Ya, ITEQ, Rogers, 华正, Elite Material (EMC), Isola (Tg135 / Tg150 / Tg170, CAF resistance, CTI > 600, halogenated and halogen-free) |
Prototype and mass-production values are listed separately and are not interchangeable. Every value is confirmed against your files, the selected material and the assigned facility during engineering review.
| Parameter | Prototype | Mass production |
|---|---|---|
| Layer count (max) | 20L | 18L |
| Panel size | 400 × 540 mm | 400 × 540 mm |
| Finished board thickness | 0.25–5.0 mm | 0.25–3.2 mm |
| Min trace / space | 1.5 / 1.5 mil | 2 / 2 mil |
| Min hole-to-trace clearance | 4 mil | 5 mil |
| Copper weight | 1/3–3 oz | 1/3–2 oz |
| Layer registration accuracy | 0.8 mil | 1 mil |
| Min through-hole diameter | 0.075 mm | 0.10 mm |
| Min blind via diameter | 0.05 mm | 0.05 mm |
| Max aspect ratio | 16:1 | 12:1 |
| Etching tolerance | ±10% / ±0.8 mil | ±10% / ±1 mil |
| Min solder mask bridge | 2 mil | 3 mil |
| Impedance control tolerance | ±5% | ±7% |
| Surface finish | ENIG, electrolytic gold, HASL, Ni/Pd/Au, thick electrolytic gold, immersion tin, immersion silver, OSP, carbon | ENIG, electrolytic gold, HASL, Ni/Pd/Au, thick electrolytic gold, immersion tin, immersion silver, OSP |
| Supported structures | Symmetrical single-sided flex, multilayer flex, flex gold fingers, air gap, asymmetrical stack-up, HDI, outer-layer flex with press-fit, bookbinder, high-frequency and high-speed | Symmetrical single-sided flex, multilayer flex, flex gold fingers, air gap, asymmetrical stack-up, HDI, outer-layer flex with press-fit, bookbinder, high-frequency and high-speed |
| Material types | Shengyi, 宏仁, 台虹, DuPont, Panasonic, Rogers, ITEQ | Shengyi, 宏仁, 台虹, DuPont, Panasonic, Rogers, ITEQ |
Prototype and mass-production values are listed separately and are not interchangeable. Every value is confirmed against your files, the selected material and the assigned facility during engineering review.
| Parameter | Prototype | Mass production |
|---|---|---|
| Layer count (max) | 12 | 16 |
| Min dielectric thickness | 12.5 µm | 12.5 µm |
| Min BGA pitch | 150 µm | 100 µm |
| Min board thickness | 50 µm | 50 µm |
| Max panel size | 610 × 1200 mm | 610 × 1200 mm |
| Base copper thickness | 9–35 µm | 6–35 µm |
| Min trace / space | 40 / 40 µm | 35 / 35 µm |
| Pattern registration tolerance | ±50 µm | ±20 µm |
| Min pattern-to-edge clearance | 0.10 mm | 0.07 mm |
| Etching tolerance | ±20 µm | ±15 µm |
| Min through-hole diameter | 0.10 mm | 0.075 mm |
| Min blind via diameter | 0.05 mm | 0.05 mm |
| Hole position tolerance | ±0.05 mm | ±0.05 mm |
| Impedance control tolerance | ±10% | ±5% |
| Outline tolerance | ±0.10 mm | ±0.05 mm |
| Surface finish | HASL, ENIG, immersion silver, OSP, Ni/Pd/Au, electrolytic gold | HASL, ENIG, immersion silver, OSP, Ni/Pd/Au, electrolytic gold |
| Stiffener type | FR-4, PI, stainless steel | FR-4, PI, stainless steel |
| Stiffener registration tolerance | ±0.20 mm | ±0.10 mm |
| HDI capability | 4-layer any-layer interconnect | 6-layer any-layer interconnect |
| LCP material | Supported | Supported |
Prototype and mass-production values are listed separately and are not interchangeable. Every value is confirmed against your files, the selected material and the assigned facility during engineering review.
| Parameter | Prototype | Mass production |
|---|---|---|
| Material system | PTFE + ceramic, PTFE + glass fiber + ceramic, PTFE + glass fiber | PTFE + ceramic, PTFE + glass fiber + ceramic, PTFE + glass fiber |
| Layer count (max) | 24L | 20L |
| Panel size (max) | 850 × 700 mm | 720 × 650 mm |
| Profile tolerance | ±0.05 mm | ±0.10 mm |
| Slot tolerance | Normal slot ±0.08 mm, short slot ±0.10 mm | Normal slot ±0.10 mm, short slot ±0.13 mm |
| Layer registration | 2 mil | 3 mil |
| Hybrid lamination | PTFE + hydrocarbon ceramic + FR-4 | PTFE + hydrocarbon ceramic + FR-4 |
| Min hole size | 0.075 mm | 0.10 mm |
| Min hole-wall spacing | 0.20 mm | 0.25 mm |
| Hole diameter tolerance | ±0.05 mm | ±0.075 mm |
| Max aspect ratio | 16:1 | 12:1 |
| Hole copper uniformity | COV ≤ 5% | COV ≤ 7% |
| Resin-filled via aspect ratio | 12:1 | 12:1 |
| Resin-filled via type | Through holes, blind and buried vias | Through holes, blind and buried vias |
| Trace width tolerance | ±0.6 mil | ±1 mil |
| Impedance tolerance | ±5% | ±8% |
| Warpage | 0.50% | 0.75% |
| Special processes | POFV (VIPPO), hybrid and local hybrid lamination, long/short, stepped and segmented gold fingers, stepped slots, back drilling, sidewall metallization, N+N, double-sided press-fit mechanical blind vias, local thick copper, high-temperature lamination, copper/silver paste via filling, skip vias, HDI | POFV (VIPPO), hybrid and local hybrid lamination, long/short, stepped and segmented gold fingers, stepped slots, back drilling, sidewall metallization, N+N, double-sided press-fit mechanical blind vias, local thick copper, high-temperature lamination, copper/silver paste via filling, skip vias, HDI |
| Material brands | Shengyi, ITEQ, TUC, Panasonic (M4/M6/M7/M8), Rogers, Taconic, Wangling, 睿龙, 国能 | Shengyi, ITEQ, TUC, Panasonic (M4/M6/M7/M8), Rogers, Taconic, Wangling, 睿龙, 国能 |
Prototype and mass-production values are listed separately and are not interchangeable. Every value is confirmed against your files, the selected material and the assigned facility during engineering review.
What to send
Files and details for a PCB review
- Gerber (RS-274X) or ODB++ data with drill files
- Fabrication drawing with material, thickness and finish
- Stack-up and impedance targets, if any
- Quantity for prototype and production
- Special requirements such as testing or packaging
Start a new PCB project
Send your files and planned quantities. We will confirm the open engineering points before quoting.
PCB FAQs
Do you issue an instant price?
No. Each project is reviewed by engineering first, and the quotation confirms scope, price, lead time and terms before payment.
Can you suggest a stack-up?
Yes. Share your layer count, thickness and impedance targets and we will propose or check a stack-up during review.
How are my files handled?
Technical files are kept out of public links and shared only within your project. Please do not send them through public channels.



